Cummins ISX12 CM2250 (2010-12) Fault Code: 1361 PID: 372 SPN: 974 FMI: 4 Remote Accelerator Pedal or Lever Position Sensor 1 Circuit- Voltage Below Normal or Shorted to Low Source
The remote accelerator position sensor is a potentiometer attached to the remote accelerator lever. The remote accelerator position sensor varies the signal voltage to the engine control module (ECM) as the remote accelerator lever is depressed and released. Low signal voltage is received by the ECM when the remote accelerator lever is at 0 percent. A high signal voltage is received by the ECM when the remote accelerator is at 100 percent. The remote accelerator pedal position circuit contains a remote accelerator pedal position 5 volt supply, remote accelerator pedal position return, and remote accelerator pedal position signal.
The remote accelerator pedal or lever location varies with each original equipment manufacturer (OEM). Refer to the equipment manufacturer service information.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes
The ECM detected the remote accelerator pedal signal voltage less than 0.132-VDC for more than 20 seconds.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp immediately after the diagnostic runs and fails.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
The Reset All Faults command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the malfunction indicator lamp for on-board diagnostics applications.
If troubleshooting an intermittent accelerator problem:
The remote accelerator pedal or lever position sensor signal voltage can be monitored with INSITE? electronic service tool, while flexing the harness to locate the intermittent connection. Intermittent connections will show up as abrupt changes in signal voltage displayed by INSITE? electronic service tool.
Possible causes of this fault code include:
Remote accelerator pedal or lever position signal shorted to engine ground or RETURN wires in the OEM harness or sensor
Damaged remote accelerator pedal or lever position sensor
Open circuit in the remote accelerator SIGNAL, SUPPLY, or RETRUN wire in the harness or connectors.
Note: The three wires in the remote accelerator position sensor circuit must be twisted together.
For intermittent power supply and datalink communication issues with aftertreatment components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing, or intermittent connections.
1) OEM harness
2) ECM calibration
Bendix Acom Pro 2022 v3 ( 1 PC ) BENDIX 2022 V3Bendix $85.00
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2Trucks software $35.00
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )Trucks software $85.00
SERVICE MANUAL MACK V-MAC IIIMACK $25.00
SERVICE MANUAL DETROIT DD_PLATFORM_WIRINGDETROIT $60.00
SERVICE MANUAL HINO FD.FE.FF.SG 2003HINO $37.00
VOLVO D13 ENGINE service manualTRUCK MANUALS $22.00
SERVICE MANUAL Fuso FK & FM Series 1992-1995FUSO $24.00
MANUAL SERVICE DEUTZ AGROTRON 130-140-155-165 MK3DEUTZ $37.00
SERVICE MANUAL DETROIT DIESEL Series 92DETROIT $38.00
MANUAL SERVICE DEUTZ AGROTRON 230-260DEUTZ $30.00
SERVICE MANUAL BOBCAT 316 SMSBOBCAT $45.00