Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 2368 PID: S82 SPN: 1112 FMI: 3/3 Engine Brake Actuator Driver 3 Circuit – Voltage Above Normal or Shorted to High Source
Lamp:
Amber
Reason:
Open circuit or high voltage detected at the engine brake solenoid number 3 signal circuit.
Effect:
Possible reduce engine braking performance.
Circuit Description:
The Engine Control Module (ECM) controls engine braking on cylinders 1 and 2 by sending a signal to engine brake solenoid 1. The ECM controls engine braking on cylinders 3 and 4 by sending a signal to engine brake solenoid number 2. The ECM controls engine braking on cylinders 5 and 6 by sending a signal to engine brake solenoid 3.
Component Location:
The engine brake solenoids are located under the valve cover. The engine brake solenoids are controlled through the engine harness from the ECM.
Conditions for Running the Diagnostics:
This diagnostic runs when the keyswitch is in the ON position and when the PWM device is being energized or de-energized. In some cases the diagnostics can also run at some fixed intervals.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected the engine brake 3 Pulse-Width Modulated (PWM) signal was detected to be system voltage when the PWM signal was turned off.
Action Taken When the Fault Code is Active:
1. The ECM illuminates the amber check engine light immediately when the diagnostic runs and fails.
2. The engine brake 3 circuit will be disabled.
Conditions for Clearing the Fault Code:
1. To validate the repair, drive the vehicle and operate the engine brakes. This will allow the diagnostic to run. If the fault code does not become active again, the repair has been validated.
2. The fault code status displayed by the diagnostic tool will change to inactive immediately after the diagnostic runs and passes.
3. The ECM will turn off the amber check engine lamp after the diagnostic runs and passes.
4. The “reset all faults” command in the diagnostic tool can be used to clear active and inactive faults.
Shop Talk:
Possible causes of this fault are:
1. A short circuit to battery in the engine harness.
2. A malfunctioning engine brake solenoid.
Related
-
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5 -
download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi $76.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U2105 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL DETROIT DIESE LDDEC VI – CPC Vehicle Interface Harness Schematic
DETROIT $15.00Rated 0 out of 5 -
SERVICE MANUAL Carrie Genesis R70 Genesis R90 Genesis TR1000 Multi -Temp
CARRIE $25.00Rated 0 out of 5