Cummins ISX15 CM2250 (2010-12) Fault Code: 3526 PID: SPN: 84 FMI: 9 Wheel-Based Vehicle Speed- Abnormal Update Rate
Normally, switches, accelerators, and other components are connected to the engine electronic control module (ECM) directly through individual wires. Multiplexing allows those same components to be hard wired to an original equipment manufacturer (OEM) vehicle electronic control unit (VECU) or transmission electronic control unit (ECU) in the cab. Then component values and states from components such as sensors, accelerators and switches can be transmitted from the OEM VECU to the Cummins? engine ECM over the SAE J1939 data link.
Messages sent from OEM VECUs or transmission ECUs are received by the Cummins? engine ECM and used for controlling the engine. The Cummins? ECM and OEM VECU(s) must be configured properly so that proper operation of the multiplexed components will occur.
The SAE J1939 data link wiring and the SAE J1939 devices vary by OEM options.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the key switch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes
The ECM did not receive a message from the multiplexed device.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will turn off the MIL after three consecutive trips where the diagnostic runs and passes.
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
When this fault code is active, some multiplexed devices may not function as desired.
Possible causes of this fault code include:
When the ECM is set up properly (components enabled and OEM VECU source addressed correctly) to receive information from an OEM VECU, but the OEM VECU is actually transmitting a message that says that component is not available for multiplexing. This can be caused when a multiplexed component is enabled in the Cummins? ECM, but the OEM VECU source address of the VECU transmitting the component message is incorrect in the Cummins? ECM, or the OEM VECU is not set up to transmit the multiplexed component message.
This fault can also be caused by a bad J1939 data link connection between the OEM VECU and Cummins? ECM, a bad connection between the component and the OEM VECU, a bad OEM VECU, or a bad Cummins? ECM. It may be necessary to contact the OEM for proper multiplexing configuration.
It is possible to use INSITE? electronic service tool to monitor multiplexed components.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
For intermittent power supply and datalink communication issues with Aftertreatment Components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing or intermittent connections.
1) OEM harness
2) ECM failure
Detroit Diagnostic Link (DDDL 8.09) Engineering level 10Detroit $40.00
Perkins SPI2 2018A Dealer Parts and ServicePerkins $50.00
Thermo King EPC 2012Thermo King $45.00
Wabco ToolBox plus 126.96.36.199 + ECAS CAN2 v3.00 Diagnostics SoftwareTrucks software $84.00
Navistar Engine Diagnostics (NEDS) Software 2023Navistar $96.00
DOOSAN DMS-5 3.1.3 [2023.11] diagnostic software 1PCDOOSAN $106.00
Wabco PIN Code Calculator Diagnostic Software PIN 1 PIN 2Trucks software $10.00
DETROIT DT12 TRANSMISSIONS – Service manual – PDFDETROIT $55.00
SERVICE MANUAL BOBCAT 425-428 smsBOBCAT $57.00
SERVICE MANUAL BOBCAT 329 smsBOBCAT $55.00
SERVICE MANUAL BOBCAT 943 smsBOBCAT $40.00
SERVICE MANUAL BOBCAT 653 smsBOBCAT $45.00
SERVICE MANUAL Carrie Supra 550 650 750 850 950CARRIE $20.00
SERVICE MANUAL DETROIT DD5DETROIT $50.00
SERVICE MANUAL Carrie Electra NEE-43/44CARRIE $20.00