Cummins X12 CM2350 X119B (2018 & Newer) Fault Code: 331 PID: SID 2 SPN: 652 FMI: 5 Injector Solenoid Driver Cylinder 2 Circuit- Current Below Normal or Open Circuit
The injector solenoid valves control fueling quantity and injection timing. The engine control module (ECM) energizes the solenoid by closing a high-side and a low-side switch. Each injector circuit has a dedicated low-side switch that completes the circuit path to ground inside the ECM.
The engine harness connects the ECM to the pass-through connector(s) that are located in the rocker housing. Internal injector harnesses are located under the valve cover and connect the injectors to the engine harness at the pass-through connector(s).
Conditions for Running the Diagnostics
This diagnostic runs continuously when the engine is running.
Conditions for Setting the Fault Codes
The Engine Control Module (ECM) detected a circuit error on an injector(s) circuit. The ECM will disable the injection event for the affected injector(s) circuit if there is excessive current.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
The injector will be disabled for the malfunctioning cylinder.
Exhaust Gas Recirculation (EGR) valve operation will be disabled.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
If more than one injector fault code is occurring, and the faults occur for injector circuits in the same bank, a short circuit exists.
If a fault condition is intermittent, and especially if more than one injector fault code is occurring, look for a wire harness that can short to components inside the rocker housing or a short circuit to ground in the injector solenoid. When looking for short circuits in the injector harnesses, pay particular attention to the wire insulation, making sure there are no shorts to a rocker lever. An intermittent short can result if the wiring harness insulation rubs through near a rocker lever. An intermittent short can cause a single injector fault code.
If the fault(s) occur intermittently, the engine can exhibit a misfire even if the injector circuit fault code does not always register. If a single cylinder exhibits misfires, look for an open circuit problem. If several cylinders on the same bank exhibit misfires, look for a short circuit anywhere in the bank of cylinders.
Possible causes of a single injector fault include:
Open circuit in the engine harness(es) or injector solenoid
High resistance in a single injector or injector solenoid
Extremely low resistance in an injector solenoid (injector shorted internally but not to ground)
Malfunctioning or damaged ECM.
Possible causes of multiple injector fault codes in the same bank of injectors include:
Short circuit in the engine harness(es) – either shorts to ground or to other wires in the engine harness
Short circuit in any of the three injectors in the bank – shorts to ground
Malfunctioning or damaged ECM.
Same Bank Fault Codes:
Bank 1 – Front Bank: Fault Codes 322, 324, 331
Bank 2 – Rear Bank: Fault Codes 323, 325, 332.
1) Injector harness
2) Engine harness
3) Injector 1,2,3 failure
4) ECM calibration
Detroit BackDoor Password Generator V1 V2Detroit $30.00
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023John Deere $250.00
Diamond Logic Builder DLB 2019 Database 2019Navistar $50.00
Isuzu E-IDSS Diagnostic Service System 04.2022 ( 1 PC )ISUZU $126.00
Volvo Intermediate Storage File Encryptor/Decryptor (Editor) VISFED 0.3.2Trucks software $35.00
VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )Trucks software $80.00
Bendix 6.16 ACom Diagnostics ( bendix software trucks )Bendix $35.00
Meritor Wabco Tool Box 12.12Trucks software $40.00
Magic Tuner [paccar, Maxxforce, Detroit, Caterpillar, Delete]Magic Tuner $50.00
Wabco PIN Code Calculator Diagnostic Software PIN 1 PIN 2Trucks software $10.00
CUMMINnSsg INSITEr 220.127.116.11 PRO + ZAP-ITcummisznn $70.00
SERVICE MANUAL BOBCAT 980 smsBOBCAT $32.00
SERVICE MANUAL Fuso FH Series 1996-2001FUSO $28.00
SERVICE MANUALDAF FUSO CANTER 2012-2016FUSO $23.00
SERVICE MANUAL BOBCAT 320-322BOBCAT $65.00
SERVICE MANUAL BOBCAT 974-975 smsBOBCAT $35.00
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2014 & Newer)INTERNATIONAL ENGINES $17.00
SERVICE MANUAL 3000 and 4000 Series Gen 5 ALLISONAllison $18.00
SERVICE MANUAL EATON Gen 2 – Automated TransmissionsEATON $28.00
SERVICE MANUAL EATON UltraShift & AutoShift (Gen 3)EATON $36.00
SERVICE MANUAL EATON UltraShift PLUSEATON $40.00