The immobilizer function is a part of a system that prevents the engine from starting if the correct ignition key is not used. After ignition ON, a security code is broadcast from the ECM control unit to the immobilizer control unit or the Instrument cluster (US market). Engine start is permitted if a correct response message is received within a certain number of tries and within a certain time from the immobilizer control unit.
Conditions for diagnostic trouble code (DTC):
1) Communication fault between Instrument cluster (IC) and Engine control module (ECM)
Observable symptoms
1) Engine cannot be started
Probable cause
1) Instrument cluster
2) Data link
-
Volvo Impact 2021 Trucks & Buses 06.2021 DVD 9116 Spare Parts Catalog
Trucks software $55.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0973 Shift Solenoid 1 (SS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1891 Throttle Position Sensor (TPS) PWM Signal – Low Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2671 Actuator Supply Voltage 2 (HSD2) – High (Batt)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0100 Lost Communication With ECM A
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2730 Pressure Control Solenoid 1 (PCS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5
-
Detroit DD15 EPA07 (2007-09) Fault Code: SPN 1077 FMI 7 (MCM) Rail Pressure Deviation is Greater the 200 Bar for Eight Seconds
DD15 EPA07 (2007-09)Rated 0 out of 5 -
Volvo All Engines (2010 Emissions) Fault Code: SPN 1136 FMI 4 PID: PPID 55 Engine Control Module (ECM) Temperature
All Engines (2010 Emissions)Rated 0 out of 5 -
Detroit DD15 EPA07 (2007-09) Fault Code: SPN 723 FMI 31 (MCM) Backwards Running Engine Detected
DD15 EPA07 (2007-09)Rated 0 out of 5 -
Allison 3000 & 4000 Gen 4 Fault Code: U0010 CAN1/SAE J1939 Bus Reset Counter Overrun
3000 & 4000 Gen 4Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: U183F CAN Communication – Message (VDC1) Out of Range, VDC Brake Light Request from Brake System
MX (2004 Emissions)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 974 FMI 3 (CPC) Remote Accelerator Pedal Circuit Failed High
DD15 GHG14 (2014-16)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P203900 PID: ACM Reductant Injection Air Pressure Sensor “A”
All Engines (2017 Emissions)Rated 0 out of 5 -
Detroit DD16 EPA07 (2007-09) Fault Code: SPN 247 FMI 14 (CPC) MCM Reported Ash Mileage is Lower than the CPC Stored Value
DD16 EPA07 (2007-09)Rated 0 out of 5