Volvo All Engines (2010 Emissions) Fault Code: SPN 631 FMI 4 PID: PSID 7 Calibration memory

Related products

• 

  Cummins ISM CM870 (2003-06) Fault Code: 2359 PID: P411 SPN: 411 FMI: 0/16 EGR Differential Pressure Sensor – Data Valid but Above Normal Operating Range – Moderately Severe Level. EGR differential pressure sensor failed automatic calibration procedure or EGR differential pressure reading not valid for engine operating conditions.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 432 PID: SID 230 SPN: 558 FMI: 13 Accelerator Pedal or Lever Idle Validation Circuit – Out of Calibration. Voltage at idle validation on-idle and off-idle circuit does not match accelerator pedal position.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2638 PID: SPN: 3050 FMI: 13 Catalyst Efficiency – Out of Calibration. The temperature increase across the aftertreatment diesel oxidation catalyst is lower than expected.

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 1896 PID: SID 146 SPN: 2791 FMI: 13 EGR Valve Controller- Out of Calibration

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 1691 PID: SPN: 3250 FMI: 13 Catalyst Efficiency – Out of Calibration. The temperature increase across the aftertreatment diesel oxidation catalyst is lower than expected.

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 2765 PID: SID 392 SPN: 2797 FMI: 13 Engine Injector Bank 1 Barcodes- Out of Calibration

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3717 PID: SPN: 3226 FMI: 13 Aftertreatment Outlet Nox Sensor- Out of Calibration

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2765 PID: SPN: 2797 FMI: 13 Engine Injector Bank 1 Barcodes – Out of Calibration. Invalid injector barcode information has been entered.

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 4431 PID: SPN: 3360 FMI: 13 Aftertreatment Diesel Exhaust Fluid Controller- Out of Calibration

  Cumminz
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 2449 PID: SID 027 SPN: 641 FMI: 13 VGT Actuator Controller – Out of Calibration. The VGT has failed the automatic calibration procedure at initial key-ON.

  DTC TRUCKS
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 286 PID: SID 231 SPN: 639 FMI: 13 SAE J1939 Multiplexing Configuration Error – Out of Calibration. The ECM expected information from a multiplexed device but only received a portion of the necessary information.

  Cumminz