Volvo All Engines (2010 Emissions) Fault Code: SPN 631 FMI 5 PID: PSID 7 Calibration memory

Related products

• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 432 PID: SID 230 SPN: 558 FMI: 13 Accelerator Pedal or Lever Idle Validation Circuit – Out of Calibration. Voltage at idle validation on-idle and off-idle circuit does not match accelerator pedal position.

  Cumminz
• 

  Cummins ISX CM870 (2003-06) Fault Code: 2348 PID: 27 SPN: 27 FMI: 13/13 EGR Valve Self Calibration. EGR valve failed automatic self calibration procedure.

  Cumminz
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2449 PID: SID 027 SPN: 641 FMI: 13 VGT Actuator Controller – Out of Calibration. The VGT has failed the automatic calibration procedure at initial key-ON.

  DTC TRUCKS
• 

  Cummins ISM CM875 (2003-06) Fault Code: 2348 PID: 27 SPN: 27 FMI: 13/13 EGR Valve Self Calibration. EGR valve failed automatic self calibration procedure.

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 346 (MD) PID: SID 253 SPN: 630 FMI: 12 Engine Control Module Calibration Memory Software- Bad Intelligent Device or Component

  Cumminz
• 

  Cummins ISX11.9 CM2250 (2010-12) Fault Code: 3697 PID: SID 254 SPN: 630 FMI: 12 Engine Control Module Calibration Memory- Bad Intelligent Device or Component

  Cumminz
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1896 PID: SID 146 SPN: 2791 FMI: 13 EGR Valve Controller – Out of Calibration. The EGR valve has failed the automatic calibration procedure at initial key-on.

  DTC TRUCKS
• 

  Cummins ISX CM870 (2003-06) Fault Code: 2359 PID: P411 SPN: 411 FMI: 0/16 EGR Differential Pressure Sensor – Data Valid but Above Normal Operating Range – Moderately Severe Level. EGR differential pressure sensor failed automatic calibration procedure or EGR differential pressure reading not valid for engine operating conditions.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 2638 PID: SPN: 3050 FMI: 13 Catalyst Efficiency – Out of Calibration. The temperature increase across the aftertreatment diesel oxidation catalyst is lower than expected.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 286 PID: SID 231 SPN: 639 FMI: 13 SAE J1939 Multiplexing Configuration Error – Out of Calibration. The ECM expected information from a multiplexed device but only received a portion of the necessary information.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3697 PID: SID 254 SPN: 630 FMI: 12 Engine Control Module Calibration Memory – Bad Intelligent Device or Component.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 346 PID: 253 SPN: 630 FMI: 12 Engine Control Module Calibration Memory Software – Bad Intelligent Device or Component.

  Cumminz