Volvo Engine D12D AE E3 (Tier 3) Fault Code: PPID123 FMI 3 EPG 2 Start And Warmhold

Related products

• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 427 PID: SID 231 SPN: 639 FMI: 9 J1939 Datalink – Abnormal Update Rate. Communication between the electronic control module (ECM) and another device on the SAE J1939 data link has been lost.

  Cumminz
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 427 PID: SID 231 SPN: 639 FMI: 9 J1939 Datalink – Abnormal Update Rate. Communication between the electronic control module (ECM) and another device on the SAE J1939 data link has been lost.

  DTC TRUCKS
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 115 PID: 115 SPN: 115 FMI: 2 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect. The engine control module (ECM) has detected that the primary and backup speed sensor signals are connected backwards.

  Cumminz
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect. Accelerator position sensor number 1 and number 2 are reading different values.

  DTC TRUCKS
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 431 PID: SID 230 SPN: 558 FMI: 2 Accelerator Pedal or Lever Idle Validation Circuit – Data Erratic, Intermittent, or Incorrect. Voltage detected simultaneously on both idle validation and off-idle validation switches.

  DTC TRUCKS
• 

  Allison 1000 and 2000 Series Gen 4 (2005-11) Service manual

  Allison $10.00
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 115 PID: 190 SPN: 612 FMI: 2 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect. The engine control module (ECM) has detected that the primary and backup speed sensor signals are connected backwards.

  DTC TRUCKS
• 

  PACCAR PX-6 CM2150 (2007-09) Fault Code: 731 PID: SID 064 SPN: 723 FMI: 7 Engine Speed/Position Camshaft and Crankshaft Misalignment – Mechanical System Not Responding Properly or Out of Adjustment. Engine position signal from the engine speed sensor and camshaft position sensor do not match.

  DTC TRUCKS
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 432 PID: SID 230 SPN: 558 FMI: 13 Accelerator Pedal or Lever Idle Validation Circuit – Out of Calibration. Voltage at idle validation on-idle and off-idle circuit does not match accelerator pedal position.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 431 PID: SID 230 SPN: 558 FMI: 2 Accelerator Pedal or Lever Idle Validation Circuit – Data Erratic, Intermittent, or Incorrect. Voltage detected simultaneously on both idle validation and off-idle validation switches.

  Cumminz
• 

  Cummins ISB6.7 CM2150 (2007-09) Fault Code: 1663 PID: None SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  Cumminz
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2636 PID: SID 027 SPN: 641 FMI: 9 VGT Actuator Driver Circuit – Abnormal Update Rate. No communications on the J1939 data link between the engine ECM and the smart VGT controller.

  DTC TRUCKS
• 

  Cummins ISB4.5 CM2150 Fault Code: 1242 PID: 91 SPN: 91 FMI: 2 Accelerator Pedal or Lever Position Sensor 1 and 2 – Data Erratic, Intermittent, or Incorrect.

  Cumminz
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 2635 PID: SID 027 SPN: 641 FMI: 11 VGT Actuator Driver Circuit – Condition Exists. A calibration mismatch between the VGT actuator and the ECM has been detected.

  DTC TRUCKS
• 

  PACCAR PX-8 CM2150 (2007-09) Fault Code: 1663 PID: SPN: 3241 FMI: 11 Catalyst Inlet Temperature Sensor Swapped with Outlet – Condition Exists. The inlet and outlet catalyst temperature sensor connections are swapped.

  DTC TRUCKS