Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
CIRCUIT DESCRIPTION:
This DTC sets when the TCM detects no communication on the CAN1 backbone harness for a period of time.
ACTION TAKEN WHEN THE DTC SETS:
1. The CHECK TRANS light is not illuminated.
2. DTC is stored in the TCM history.
3. SEM operation is not active, if applicable.
4. Default values are substituted for missing data, e.g., engine throttle percentage, engine torque, engine coolant temperature.
5. The TCM freezes shift adapts (DNA).
CONDITIONS FOR CLEARING THE DTC:
Use the diagnostic tool to clear the DTC from the TCM history. The DTC automatically clears the DTC from the DTC history if the vehicle completes 40 warm-up cycles without the DTC recurring.
DIAGNOSTIC AIDS:
DTC U0073 indicates that a CAN1 bus hardware error has occurred. This code may be caused by:
1. Miswired or defective OEM controllers, OEM components, or OEM circuits attached to CAN 1.
2. Defective TCM.
An active DTC U0073 may prevent the diagnostic tool from communicating with the TCM. The J-47276 TCM Reflash Harness may be used to confirm that the TCM is operational. Connect the J-47276 TCM Reflash Harness to the TCM and leave the OEM harness disconnected. Provide input power from the J-42455-A Load Box.
4. CAN1 and CAN2 devices must not be interconnected because they are not compatible with each other. CAN1 operates at 250 kbps data rate and CAN2 operates at 500 kbps data rate.
5. For proper datalink communications, it is necessary to have two 120 Ω resistors installed in parallel across the CAN1 High and CAN1 Low terminals. Resistance across CAN1 High and CAN1 Low should measure 60 Ω when wired correctly.
6. The diagnostic tool Data Bus Viewer may be selected from the File Menu to monitor or log SAE J1939 datalink messages.
NOTE: The OEM transmission warranty, or the extended coverage for parts and labor, does not cover the repair or replacement of OEM or bodybuilder provided components or any external wire harnesses not provided by the OEM.
Before repairing or replacing these components or circuits that caused a transmission issue, always contact the vehicle OEM call center and/or the vehicle OEM or bodybuilder service representative to verify the warranty coverage and proper payment arrangements, arrange an alternate sublet or repair plan (if needed), and get troubleshooting assistance for the repair (such as vehicle schematics, DTC trees, parts assistance, etc.).
Related
-
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere $250.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0100 CAN Bus ECM Error
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1041 J1850 (Class 2) ABS Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0122 Pedal Position Sensor Circuit Low Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2810 Solenoid G Electrical
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1096 J1850 (Class 2) IPC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0873 Transmission Pressure Switch Solenoid E Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1688 Unmanaged Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL INTERNATIONAL ENGINE VT275 (2005 & Newer)
INTERNATIONAL ENGINES $27.00Rated 0 out of 5