Cummins ISX12 CM2250 (2010-12) Fault Code: 2777 PID: SID 390 SPN: 3703 FMI: 31 Particulate Trap Active Regeneration Inhibited Due to Inhibit Switch- Condition Exists
The OEM truck manufacturer can install a permit switch in the dash or send an inhibit message via the J1939 data link to the engine ECM. The function of the inhibit message is to prevent the aftertreatment system from performing mobile regenerations. The purpose of this fault code is to inform the technician that the permit switch was disabled when Fault Code 1921, 1922, or 2639 was set active or when the system was requesting an active regeneration of the aftertreatment system. This fault code can indicate the reason that high aftertreatment soot load fault codes are logged.
The aftertreatment diesel particulate filter is located in the exhaust system and is installed by the original equipment manufacturer (OEM). The permit switch can be an actual switch in the vehicle dash or it can be a J1939 message sent via the J1939 data link. Refer to the OEM service manual.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the keyswitch is in the ON position.
Conditions for Setting the Fault Codes
This fault code is triggered if the permit switch is disabled when Fault Code 1921, 1922, or 2639 is activated for high soot load levels in the diesel particulate filter or when the ECM is requesting active regeneration of the aftertreatment diesel particulate filter.
Action Taken When the Fault Code is Active
The ECM logs the fault code immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code
To validate the repair, start the engine and let it idle for 1 minute with the permit switch enabled.
The fault code status displayed by INSITE? electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes
The ?Reset All Faults? command in INSITE? electronic service tool can be used to clear active and inactive faults.
If this fault code is active and there has been damage to the aftertreatment system, the permit switch can possibly have prevented the aftertreatment system from performing a mobile (active) regeneration.
Consult with the OEM if the aftertreatment system has malfunctioned due to the permit switch.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
For intermittent power supply and datalink communication issues with Aftertreatment Components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing or intermittent connections.
1) ECM calibration
Volvo PROSIS Offline 2019 Parts Catalog Installation ServiceTrucks software $45.00
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )Trucks software $85.00
Navistar Engine Diagnostics (NEDS) Software 2023Navistar $96.00
Wabco ToolBox plus 220.127.116.11 + ECAS CAN2 v3.00 Diagnostics SoftwareTrucks software $84.00
SERVICE MANUAL TROUBLESHOOTING TC10 5TH GENERATION ALLISONAllison $19.00
SERVICE MANUAL BOBCAT 5600 SMSBOBCAT $62.00
SERVICE MANUALDAF Fuso FE & FG Series 1992-1995FUSO $27.00
SERVICE MANUAL BOBCAT 310 – 313 SMSBOBCAT $45.00
SERVICE MANUAL MACK Air & Brakes systemMACK $28.00
SERVICE MANUAL BOBCAT 3450 smsBOBCAT $35.00
SERVICE MANUAL BOBCAT 2410 smsBOBCAT $34.00
SERVICE MANUAL BOBCAT 2000 smsBOBCAT $30.00
SERVICE MANUAL International Engines DT466E & DT530E (1999 & Older)INTERNATIONAL ENGINES $31.00