Volvo All Engines (2004 Emissions) Fault Code: PID 100 FMI 3 Engine Management System Module-Engine Oil Pressure
Fault Condition: The Electronic Malfunction Lamp (EML) will illuminate when the EOP Sensor’s signal line voltage is less than 0.3 volts or greater than 4.75 volts. If the signal line voltage returns to between 0.3 volts and 4.75 volts the fault will become inactive.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect EMS Module connectors A and B. Disconnect Engine Oil Pressure (EOP) Switch connector. Check for continuity between Engine Oil Pressure (EOP) Sensor harness connector pin 2 (signal line) and a good ground and also check for continuity between EMS Module connector B pin 11 and all other pins on EMS Module connector A and B. If continuity exists, locate and repair the short circuit.
2) Disconnect EMS Module connector B. Check for continuity between Engine Oil Pressure (EOP) Sensor harness connector pin 1 (reference voltage line) and EMS Module harness connector B pin 17 . If there is NO continuity, repair the open in the harness reference voltage line.
3) Disconnect the Engine Oil Pressure (EOP) Sensor. Disconnect EMS Module connectors and B. Check for continuity between EMS Module harness connector B pin 11 (signal line) and all other pins in the EMS Module harness connectors A and B. If continuity exists or if there is a visual short, repair the short circuit to the signal line. If there is NO continuity or visual short, replace the EMS Module.
4) Disconnect the Engine Oil Pressure (EOP) Sensor. Disconnect EMS Module connector B. Check for continuity between EOP sensor harness connector pin 2 (signal line) and EMS Module harness connector B pin 11.
If there is NO continuity, repair the open in the harness signal line.
5) Disconnect the Engine Oil Pressure (EOP) Sensor. Disconnect EMS Module connectors A and B. Check for continuity between EMS Module harness connector B pin 17 (reference voltage line) and all other pins in EMS Module harness connectors A and B. If continuity exists or if there is a visual short, repair the short circuit to the reference voltage line. If there is NO continuity or visual short, replace the EMS Module.
6) Disconnect EMS Module connectors A and B. Disconnect the Engine Oil Pressure (EOP) Sensor. Check for continuity between EMS Module harness connector B pin 17 (reference voltage line) and all other pins in EMS
Module harness connectors A and B. Visually check EMS Module connector B pin 17 for a short circuit. If continuity exists or if there is a visual short, repair the short circuit to the reference voltage line.
If there is NO continuity or visual short circuit, replace the EMS Module.
7) Disconnect EMS Module connectors A and B. Disconnect the Engine Oil Pressure (EOP) Sensor. Check for continuity between EMS Module harness connector B pin 18 (ground line) and all other pins in EMS Module harness
connectors A and B (see Figure 59). If continuity exists or if there is a visual short circuit, repair the short to the return line. If there is NO continuity or visual short circuit, replace the EMS Module.
8) Visually inspect both sides of EMS Module connector B pin 11 for a repairable open in the signal line. If a repairable open is found, repair or replace EMS Module harness connector B.
9) Visually inspect both sides of the Engine Oil Pressure (EOP) Sensor connector for a repairable open. If there is a repairable fault or any of the pins feel loose, repair or replace the connector.
10) Remove the Engine Oil Pressure (EOP) Sensor from the oil filter assembly. Connect the EOP Sensor to a regulated air supply with an accurate pressure gauge. Connect a jumper wire between EOP Sensor pin 1 and pin 1 on the sensor harness connector. Connect a jumper wire between EOP Sensor pin 4 and a good ground. Turn the ignition key ON. Measure the voltage between EOP sensor pin 2 and a good ground at various pressures between 0 psi and 101.5 psi. If the EOP Sensor output is correct throughout the entire pressure range, reinstall the sensor and replace the EMS Module. If the EOP Sensor output is NOT correct throughout the entire pressure range,
replace the EOP Sensor and recheck the system.
Related
-
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software $85.00Rated 0 out of 5 -
DOWNLOAD NISSAN UD DIESEL PC-CONSULT DIAGNOSTIC 1.1.13 & PC-REPROMASTER 1.2.0
NISSAN UD $100.00Rated 0 out of 5 -
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5
-
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
CAT ET 2021A (Caterpillar Electronic Technician) + Factory Password (1 PC )
CAT $65.00Rated 0 out of 5 -
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5 -
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 Fault Codes: U0031 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0871 Transmission Pressure Switch Solenoid E Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1779 Engine Torque Delivered To TCM Signal
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1300 J1850 (Class 2) Serial Data Communication Link Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1892 Throttle Position Sensor Pulse Width Modulation (PWM) Signal High Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0847 Transmission Pressure Switch Solenoid D Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1016 Class 2 J1850 (Class 2) Powertrain Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2007-2009)
INTERNATIONAL ENGINES $30.00Rated 0 out of 5 -
SERVICE MANUAL DETROIT DIESEL EPA 07, EPA 10, GHG 14 TROUBLESHOOTING
DETROIT $38.00Rated 0 out of 5