Volvo All Engines (2004 Emissions) Fault Code: PID 97 FMI 3 Water in Fuel Filter Sensor
Fault Condition: This fault will become active when the EMS Module detects that the Water In Fuel Filter supply voltage is above or below preset specifications. Actual water in the fuel filter will not produce a fault.
Possible repairs:
Turn the ignition key OFF first.
1) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 8 and pin 3 of the WIFF Sensor harness connector.
If there is NO continuity, repair the open in the harness reference voltage line.
2) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 8 and a good ground. If continuity exists, repair the short to ground in the harness voltage line and retest the system.
3) Disconnect EMS Module connector B and the Water In Fuel Filter (WIFF) Sensor connector. Measure for continuity between EMS Module harness connector B pin 10 and pin 2 of the WIFF Sensor harness connector. If there is NO continuity, repair the open in the harness reference line.
4) Visually inspect EMS Module connectors A and B for dirt, loose or shorted pins or deformed contacts. If a repairable open or short is found, or the terminal feels loose, repair EMS Module harness connector.
5) Connect EMS Module connectors A and B. Connect the WIFF Sensor connector. Turn the ignition key ON. If code PID 97 is still active, replace the Water In Fuel Filter (WIFF) Sensor and retest the system. If code PID 97 is still
active, check the EMS Module and connectors A and B for dirt, loose or shorted pins, or any other repairable damage. If no problems are evident, or are NOT repairable, replace the EMS Module and retest the system.
If code PID 97 is NOT active, the diagnostic procedures have corrected the problem. Check all connectors to ensure proper contact.
6) Disconnect the EMS Module harness connectors A and B. Disconnect the harness connector from the Water In Fuel Filter Sensor. Turn the ignition key ON. Measure the battery voltage between pin 3 of the Water In Fuel Filter Sensor connector and a good ground. If there is approximately battery voltage, locate and repair the short to voltage in the signal line. If 0 volts is measured, replace the EMS Module and retest the system.
Related
-
Navistar international OnCommand service information 2018 software trucks
Navistar $50.00Rated 0 out of 5 -
PF Diagnose 2.0.2.23 Diagnostics Software 2013 – Full Heavy & Medium Duty with OBDII Support – Online Installation Service
PF Diagnose $60.00Rated 0 out of 5 -
DAF Davie Runtime v5.6.1 Davie XDc ll [02.2019] + Expire Fix 302.00 Unlock ( Windows 7 )
DAF $70.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
Eaton Service Ranger 4.9 Engineering 4.9 [05.2021] Engineering Level ( 1 PC )
Eaton $67.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 4 P0719 Brake Switch ABS Input Low
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1064 J1850 (Class 2) TBC Controller State of Health Failure
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P2771 Four-Wheel Drive Switch Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0848 Transmission Pressure Switch Solenoid D Circuit High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0872 Transmission Pressure Switch Solenoid E Circuit Stuck Closed
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U2104 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0880 TCM Supply Voltage
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0876 Transmission Reverse Pressure Switch Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P1891 Engine Throttle Position Sensor Pulse Width Modulation (PWM) Signal Low Input
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U1000 Class 2 Loss of Serial Data Communication
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0032 J1850 (Class 2) Serial Data Communication Link High
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0846 Transmission Pressure Switch Solenoid D Circuit Stuck Open
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: U0073 CAN Bus Reset Counter Overrun
1000 & 2000 Gen 4 $50.00Rated 0 out of 5 -
Allison 1000 & 2000 Gen 4 Fault Codes: P0870 Transmission Pressure Switch Solenoid E Circuit
1000 & 2000 Gen 4 $50.00Rated 0 out of 5
-
SERVICE MANUAL International Engines MaxxForce 7 (2010 & Newer)
INTERNATIONAL ENGINES $34.00Rated 0 out of 5 -
SERVICE MANUAL International Engines MaxxForce DT 9 10 (2007-2009)
INTERNATIONAL ENGINES $30.00Rated 0 out of 5