The following components are connected to a common 12?V supply
A95: Aftertreatment Diesel Particulate Filter (DPF) Atomization Module
Y76: Aftertreatment ignition coil
Y103A: Aftertreatment fuel shut-off valve
M15: Aftertreatment Fuel Pump
Y77: Aftertreatment Diesel Particulate FIlter (DPF) Combustion Air Valve
If an abnormal voltage or current is detected on the common supply a DTC is set
Conditions for diagnostic trouble code (DTC):
1) Engine Turbo Compressor Bypass Valve, Stuck in one position
Observable symptoms
1) Regeneration not possible
2) Possible engine de-rate
3) Low Power
Probable cause
1) Low air pressure
2) Charge air system leakage
3) ETCBV Hose
4) ETCBV Sealing ring
5) Engine Turbo Compressor Bypass Valve
6) ETCBV, Solenoid valve(s)
7) Turbocharger
Detailed information
1) Heat mode inhibited
-
PF Diagnose 2.0.2.23 Diagnostics Software 2013 – Full Heavy & Medium Duty with OBDII Support – Online Installation Service
PF Diagnose $60.00Rated 0 out of 5 -
CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT $45.00Rated 0 out of 5 -
Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat $110.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2723 Pressure Control Solenoid 1 (PCS1) – Stuck Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0074 CAN Communications BUS 2 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0100 Lost Communication With ECM A
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0122 Pedal Position Sensor Circuit – Low Voltage
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0974 Shift Solenoid 1 (SS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5
-
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 986 FMI 19 (CPC) Signal Source #1 or #2 is Erratic
DD15 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD13 EPA10 (2010-13) Fault Code: SPN 3236 FMI 13 (ACM) Exhaust Mass Signal Not Available via Controller are Network
DD13 EPA10 (2010-13)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 723 FMI 31 (MCM) Backwards Running Engine Detected
DD15 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD13 EPA07 (2007-09) Fault Code: SPN 84 FMI 2 (CPC) J1939 Wheel-Based Vehicle Speed Signal from Source #1 is Erratic
DD13 EPA07 (2007-09)Rated 0 out of 5 -
Detroit DD15 EPA10 (2010-13) Fault Code: SPN 3364 FMI 2 (ACM) Improper Diesel Exhaust Fluid Quality
DD15 EPA10 (2010-13)Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 175 FMI 3 (MCM) Engine Oil Temperature Circuit Failed High
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Allison WTEC II Fault Code: 53 PID: SPN: 68 FMI: Offgoing speed test (during shift), 6 to N1
AllisonRated 0 out of 5 -
Detroit DD13 EPA07 (2007-09) Fault Code: SPN 636 FMI 31 (MCM) Crankshaft Position Sensor – Error Detected
DD13 EPA07 (2007-09)Rated 0 out of 5