The Crank Speed Sensor is an inductive sensor that will generate a variable voltage signal when the sensor’s magnetic field is excited. When the engine is running the flywheel’s teeth rotate past the sensor’s tip and voltage pulses are generated. The Engine Control Module (ECM) monitors the frequency of the signal generated by the Crank Speed Sensor and calculates the engine RPM.
Conditions for diagnostic trouble code (DTC):
1) Incorrect crankshaft position (CKP) sensor signal
Observable symptoms
1) Long start time
2) Uneven operation
3) Loss of power
Probable cause
1) Flywheel sensor
2) Wiring harness
3) Flywheel
4) Electrical interference in the crankshaft position (CKP) sensor signal
5) Incorrectly installed sensor (incorrect distance to tooth wheel)
-
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0977 Shift Solenoid 2 (SS2) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1891 Throttle Position Sensor (TPS) PWM Signal – Low Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0074 CAN Communications BUS 2 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1892 Throttle Position Sensor (TPS) PWM Signal – High Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5
-
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 5363 FMI 18 (MCM) Cylinder #6 Engine Smoothness Control/Quantity Excess
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 3242 FMI 8 (ACM) Diesel Oxidation Catalyst Inlet Temperature – Signal Spike
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 70 FMI 19 (CPC) Park Brake Switch Signal from Source #1, #2, or #3 is Erratic
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P220A1C PID: EMS NOx Sensor Supply Voltage Circuit (Bank 1 Sensor 1)
All Engines (2017 Emissions)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P009700 PID: EMS Intake Air Temperature Sensor 2 Circuit Low (Bank 1)
All Engines (2017 Emissions)Rated 0 out of 5 -
Detroit DD15 EPA07 (2007-09) Fault Code: SPN 597 FMI 13 (CPC) J1939 Service Brake Switch Signal from Source #1, #2, Or #3 is Missing
DD15 EPA07 (2007-09)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 1624 FMI 19 (CPC) Tachograph Vehicle Speed Signal is Erratic
DD15 GHG14 (2014-16)Rated 0 out of 5 -
Volvo All Engines (2013 Emissions) Fault Code: P016E00 PID: EMS Closed Loop Fuel Pressure Control At Limit – Pressure Too High
All Engines (2013 Emissions)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 96 FMI 19 (CPC) Fuel Level Sensor Received Network Data in Error
DD15 GHG14 (2014-16)Rated 0 out of 5