Cummins ISL CM850 (2003-06) Fault Code: 599 PID: SID 25 SPN: 640 FMI: 14 Auxiliary Commanded Dual Output Shutdown – Special Instructions. The engine protection limit has been exceeded for the dual outputs calibrated limits.

Related products

• 

  Cummins ISB4.5 CM2150 Fault Code: 4284 PID: SPN: 5793 FMI: 9 Desired Engine Fueling State – Abnormal Update Rate.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2555 PID: SPN: 729 FMI: 3 Engine Intake Air Heater 1 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2183 PID: 477 SPN: 1072 FMI: 4 Engine Brake Actuator Driver 1 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2266 PID: SID 126 SPN: 1075 FMI: 4 Electric Lift Pump for Engine Fuel Supply Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2363 PID: SID 80 SPN: 1073 FMI: 4 Engine Brake Actuator Driver Output 2 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3139 PID: SPN: 3667 FMI: 3 Engine Air Shutoff Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3382 PID: SPN: 3058 FMI: 18 Engine Exhaust Gas Recirculation System – Data Valid But Below Normal Operating Range – Moderately Severe Level.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2369 PID: SPN: 1074 FMI: 4 Engine (Exhaust) Brake Driver Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2182 PID: 478 SPN: 1072 FMI: 3 Engine Brake Actuator Driver 1 Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3555 PID: SPN: 1081 FMI: 9 Engine Wait to Start Lamp – Abnormal Update Rate.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 2363 PID: SID 29 SPN: 1073 FMI: 4 Engine Brake Actuator Driver Output 2 Circuit – Voltage Below Normal or Shorted to Low Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3539 PID: SPN: 51 FMI: 3 Engine Intake Throttle Actuator Position Sensor Circuit – Voltage Above Normal or Shorted to High Source.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 111 PID: 629 FMI:12 Engine Control Module Critical Internal Failure – Bad Intelligent Device or Component

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3616 PID: SPN: 2633 FMI: 7 Engine VGT Nozzle Position – Mechanical System Not Responding or Out of Adjustment.

  Cumminz
• 

  Cummins ISB4.5 CM2150 Fault Code: 3542 PID: SPN: 51 FMI: 2 Engine Intake Throttle Actuator Position Sensor – Data Erratic, Intermittent, or Incorrect.

  Cumminz