“ISUZU G-IDSS Domestic Japan 2024 Diagnostic Software” has been added to your cart. View cart
The NOx sensor measures the amount of NOx in the exhaust system. The NOx sensor is connected in the J1939-2 data link. This diagnostic trouble code (DTC) indicates a NOx monitoring failure. For example; NOx sensor short- or open circuit, NOx sensor removed, NOx sensor missing signal.
Conditions for diagnostic trouble code (DTC):
1) Abnormal sensor signal
Observable symptoms
1) None
Probable cause
1) Sensor not mounted in exhaust stream
2) Charge air system leakage
3) Exhaust system leakage
4) DEF dosing system
5) NOx sensor
6) EGR Cooler
7) EGR Valve
8) Variable Geometry Turbo
-
Wabco ToolBox plus 13.7 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software $84.00Rated 0 out of 5 -
John Deere & Hitachi Parts ADVISOR 2020 [08.2020] Offline DVD Spare Parts Catalog
John Deere $120.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5 -
International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar $85.00Rated 0 out of 5 -
PACCAR Electronic Service Analyst 5.4.3.0 SW files 27.03.2021 software trucks
PACCAR $60.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0980 Shift Solenoid 3 (SS3) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1891 Throttle Position Sensor (TPS) PWM Signal – Low Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0122 Pedal Position Sensor Circuit – Low Voltage
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0976 Shift Solenoid 2 (SS2) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0074 CAN Communications BUS 2 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP
1000 & 2000 Gen 5Rated 0 out of 5
-
Detroit DD13 EPA07 (2007-09) Fault Code: SPN 596 FMI 19 (CPC) J1939 Cruise Control Enable Switch Signal from Source #1, #2, Or #3 Erratic
DD13 EPA07 (2007-09)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 3871 FMI 4 (CPC) Transmission Speed Sensor 4 04 or 3 13 Circuit Failed Low
DD15 GHG14 (2014-16)Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: U177B Accelerator Pedal 1 – Voltage Too High or Short Circuit to Supply on ECU (D420) Pin (B41)
MX (2004 Emissions)Rated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3490 FMI 4 (ACM) Post Run Indicator Lamp
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD15 GHG14 (2014-16) Fault Code: SPN 4375 FMI 5 (ACM) Diesel Exhaust Fluid Pump Circuit Failed Open
DD15 GHG14 (2014-16)Rated 0 out of 5 -
Volvo All Engines (2010 Emissions) Fault Code: SPN 411 FMI 9 PID: Engine Exhaust Gas Recirculation Differential Pressure
All Engines (2010 Emissions)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P102900 PID: EMS Cold Start Cylinder 6 Fuel Injector Offset Learning at Min Limit
All Engines (2017 Emissions)Rated 0 out of 5 -
Detroit DD13 GHG14 (2014-16) Fault Code: SPN 677 FMI 7 (MCM, CPC) Engine Starter Relay Jammed
DD13 GHG14 (2014-16)Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP
1000 & 2000 Gen 5Rated 0 out of 5 -
Detroit DD13 EPA10 (2010-13) Fault Code: SPN 3064 FMI 13 (MCM) MCM Needs to be Reprogrammed
DD13 EPA10 (2010-13)Rated 0 out of 5