The function identifies and indicates malfunction of the aftertreatment diesel particulate filter (DPF) by analyzing the pressure drop over the aftertreatment DPF. This is done by making a check for deviation between sensor value and a model pressure drop. In some extreme cases the engine will derate.
Conditions for diagnostic trouble code (DTC):
1) High differential pressure across the filter (> 35 kPa (5 psi / 10.3 in-Hg))
Observable symptoms
1) Low Power
2) Medium to high derate
Probable cause
1) Excessive smoke from the engine
2) Aftertreatment diesel particulate filter (DPF) is loaded with soot
3) Aftertreatment diesel particulate filter (DPF) is loaded with ash
4) Incomplete regeneration, driver has not allowed regeneration to complete
5) Regeneration inhibited, driver has not allowed regeneration to take place
6) Charge air system leakage
7) EGR System Faulty
8) Aftertreatment DPF Differential Pressure Sensor
-
Hino Diagnostic eXplorer 2 – Hino DX2 1.1.19.1 with keygen unlocked ( Hino trucks )
Hino $50.00Rated 0 out of 5 -
volvo Devtool Studio V2 / V3 / V4 Developer tool plus 2.6 / 2.7
Trucks software $35.00Rated 0 out of 5 -
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit $73.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P1891 Throttle Position Sensor (TPS) PWM Signal – Low Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1892 Throttle Position Sensor (TPS) PWM Signal – High Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1790 Gear Shift Module 1 Calibration Invalid
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2727 Pressure Control Solenoid 1 (PCS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2730 Pressure Control Solenoid 1 (PCS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2637 Torque Management Feedback Signal – SEM
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0974 Shift Solenoid 1 (SS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5
-
CAT 3406E (Prefix 5DS or 1LW) Fault Code: 64 PID: 105 SPN: FMI: 0 High Intake Manifold Air Temperature Warning
3406E (Prefix 5DS or 1LW)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P050013 PID: EMS Wheel-Based Vehicle Speed
All Engines (2017 Emissions)Rated 0 out of 5 -
Detroit DD15 EPA10 (2010-13) Fault Code: SPN 175 FMI 14 (MCM) Engine Oil Temperature Out of Range (Drifted Low/High)
DD15 EPA10 (2010-13)Rated 0 out of 5 -
Volvo All Engines (2013 Emissions) Fault Code: P063000 PID: ACM VIN Not Programmed or Incomplete – ECM/PCM
All Engines (2013 Emissions)Rated 0 out of 5 -
Allison WTEC II Fault Code: 62 PID: SPN: 23 FMI: Retarder oil temperature sensor, failed high
AllisonRated 0 out of 5 -
Detroit DD15 EPA10 (2010-13) Fault Code: SPN 111 FMI 3 (CPC) Coolant Level Circuit Failed High
DD15 EPA10 (2010-13)Rated 0 out of 5 -
Volvo All Engines (2013 Emissions) Fault Code: P06A61C PID: EMS Sensor Reference Voltage “A” Circuit Range/Performance
All Engines (2013 Emissions)Rated 0 out of 5 -
Volvo All Engines (2013 Emissions) Fault Code: P114500 PID: EMS Reductant Level Moderately Low
All Engines (2013 Emissions)Rated 0 out of 5