Cummins ISB CM850 (2003-06) Fault Code: 2976 PID: SPN: 3361 FMI: 2 Dosing Control Unit Temperature – Data Erratic, Intermittent, or Incorrect. An internal error has been detected in the catalyst dosing control unit.
Cummins ISB CM850 (2003-06) Fault Code: 2976 PID: SPN: 3361 FMI: 2 Dosing Control Unit Temperature – Data Erratic, Intermittent, or Incorrect. An internal error has been detected in the catalyst dosing control unit.
Fault Code 2976 is triggered when the dosing control unit internal temperature sensor is reading a different value than the other temperature sensors on the engine. This indicates a problem with the internal temperature sensor of the dosing control unit. Dosing control unit electrical supply issues that cause the dosing control unit to remain powered when the key switch is turned OFF can cause Fault Code 2976 to become active.
On-Board Diagnostics (OBD) Information (Euro 4.5 Certified Engines):
1)The ECM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
2)An engine torque derate will be activated after 50 hours of engine operation with the fault code active.
3)To validate the repair and turn off the MIL, the engine must be shut down with the keyswitch in the OFF position for a minimum of 8 hours. After the 8 hour cold soak, if the ambient temperature is below 2?C [36?F] or above 25?C [77?F] start the engine and allow it to idle for 1 minute or run the diagnostic. If these temperatures can not be achieved, calibrate the EMC to the latest version found in the calibration revisions listed in the ECM Calibration Revision History.
4)The ECM turns OFF the MIL after 1 ignition cycle that the diagnostic runs and does not fail. The MIL lamp can not be cleared with INSITE? electronic service tool. The fault code will be cleared from memory after 400 days or 9,600 hours of engine operation.
Possible repairs:
1)Replace the DEF dosing unit if damage is detected.
2)Repair or replace the OEM harness.
3)Replace the aftertreatment DEF dosing unit.
4)If necessary, calibrate the ECM.
Related
-
VOLVO PREMIUM TECH TOOL PTT 2.7.116 + APCI 2021 + devtool ( ONLINE )
Trucks software $80.00Rated 0 out of 5
-
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
Detroit Diesel Diagnostic Link DDDL 8.0 PRO PROFESSIONAL Software trucks
Detroit $25.00Rated 0 out of 5 -
premium volvo tech tool update 2.8.150 diagnostic software 1pc
Trucks software $150.00Rated 0 out of 5 -
download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN $75.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0977 Shift Solenoid 2 (SS2) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P097A Shift Solenoid 1 (SS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P097C Shift Solenoid 3 (SS3) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2671 Actuator Supply Voltage 2 (HSD2) – High (Batt)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0980 Shift Solenoid 3 (SS3) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0976 Shift Solenoid 2 (SS2) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2669 Actuator Supply Voltage 2 Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P1892 Throttle Position Sensor (TPS) PWM Signal – High Input
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2670 Actuator Supply Voltage 2 (HSD2) – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5