This diagnostic trouble code (DTC) detects faults in the main software. Faulty main software can result in engine no start symptoms.
Conditions for diagnostic trouble code (DTC):
1) Checksum fault
Observable symptoms
1) Engine does not start
Probable cause
1) Engine control module (ECM)
2) Programmed with erroneous software
3) Programming sequence interrupted
-
Scania SDP3 2.48.6 Diagnosis & Programming for VCI 3 VCI3 without Dongle
Scania $30.00Rated 0 out of 5 -
CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS $100.00Rated 0 out of 5 -
JPRO 2022 v1 Commercial Vehicle Diagnostics V1 Software Download & Installation Service ( 1 PC )
JPRO $94.00Rated 0 out of 5 -
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2764 TCC PCS Control Circuit Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0980 Shift Solenoid 3 (SS3) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2724 Pressure Control Solenoid 1 (PCS1) – Stuck On
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2761 TCC PCS Control Circuit Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0977 Shift Solenoid 2 (SS2) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2685 Actuator Supply Circuit Voltage 3 Low (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0122 Pedal Position Sensor Circuit – Low Voltage
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0074 CAN Communications BUS 2 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0100 Lost Communication With ECM A
1000 & 2000 Gen 5Rated 0 out of 5
-
Allison 1000 & 2000 Gen 5 Fault Code:P0963 Main Pressure Modulation Solenoid Circuit High
1000 & 2000 Gen 5Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: P2542 Fuel Pressure – Voltage Too High or Short Circuit to Supply on ECU (D420) Pin (A50)
MX (2004 Emissions)Rated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 511403 FMI 10 (CPC) Generator (Charging System) Terminal W – Low Voltage
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Volvo Engine D11L (Tier 4) Fault Code: PID 105 FMI 4 Intake Manifold Temperature
D11L (Tier 4)Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: U1875 CAN Communication – Message (VDC1) Out of Range, VDC Brake Light Request from Brake System
MX (2004 Emissions)Rated 0 out of 5 -
Volvo All Engines (2004 Emissions) Fault Code: SID 230 FMI 5 Idle Validation Switch
All Engines (2004 Emissions)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: P220B1C PID: EMS NOx Sensor Gas Outlet High Voltage
All Engines (2017 Emissions)Rated 0 out of 5 -
Volvo All Engines (2010 Emissions) Fault Code: SPN 1127 FMI 11 PID: PSID 98 Engine Turbocharger 1 Boost Pressure
All Engines (2010 Emissions)Rated 0 out of 5 -
Allison WTEC II Fault Code: 33 PID: SPN: 23 FMI: Sump oil temperature sensor, failed high
AllisonRated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 1077 FMI 7 (MCM) Rail Pressure Deviation is Greater the 200 Bar for Eight Seconds
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Detroit DD16 EPA10 (2010-13) Fault Code: SPN 3480 FMI 14 (MCM) Hydrocarbon Doser Fuel Line Pressure Sensor – Failed Self Test
DD16 EPA10 (2010-13)Rated 0 out of 5