“ISUZU G-IDSS Domestic Japan 2024 Diagnostic Software” has been added to your cart. View cart
The pedal message is used to calculate fuel injection.
The J1587 and J1939 serial data lines are used as the standard communication link for on-board vehicle instrumentation, off-board service diagnostics and fleet management.
The (VECU) Vehicle Electronic Control Unit is linked to the Engine Control Module (ECM) via these data lines.
Conditions for diagnostic trouble code (DTC):
1) Open circuit
2) The voltage at pin A17.PB:8 is less than 0.7?V
Observable symptoms
1) The engine does not respond when accelerator pedal is pressed.
2) Missing kick-down effect
Probable cause
1) Connector
2) Supply wire, Open circuit
3) Signal wire, Open circuit
4) Signal wire, Short circuit to ground
5) Accelerator pedal, Sensor
-
10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT $110.00Rated 0 out of 5 -
CAT Engine Reprogramming Tool for flash programming C1.8, C2.4, C3.8 & C3.3B + Guide
CAT $50.00Rated 0 out of 5
Related products
-
Allison 1000 & 2000 Gen 5 Fault Code:P2764 TCC PCS Control Circuit Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2671 Actuator Supply Voltage 2 (HSD2) – High (Batt)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:U0073 CAN Communication Bus 1 Off
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2727 Pressure Control Solenoid 1 (PCS1) Control Circuit – Open
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2641 Torque Management Feedback Signal – LRTP
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2729 Pressure Control Solenoid 1 (PCS1) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2686 Actuator Supply Circuit Voltage 3 High (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0979 Shift Solenoid 3 (SS3) Control Circuit – Low
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P0974 Shift Solenoid 1 (SS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2730 Pressure Control Solenoid 1 (PCS1) Control Circuit – High
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2684 Actuator Supply Circuit Voltage 3 Open (HSD3)
1000 & 2000 Gen 5Rated 0 out of 5 -
Allison 1000 & 2000 Gen 5 Fault Code:P2789 Clutch Adaptive Learning at Limit
1000 & 2000 Gen 5Rated 0 out of 5
-
Detroit DD16 EPA07 (2007-09) Fault Code: SPN 2791 FMI 3 (MCM) Circuit Failed High
DD16 EPA07 (2007-09)Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: U1126 CAN – Message (TSC1_SE) Time-Out from Body Builder Module
MX (2004 Emissions)Rated 0 out of 5 -
Allison 3000 & 4000 Gen 4 Fault Code: P2724 Pressure Control Solenoid 1 (PCS1) Stuck On
3000 & 4000 Gen 4Rated 0 out of 5 -
Detroit DD16 EPA07 (2007-09) Fault Code: SPN 715 FMI 5 (CPC) Digital Output 4 12 Circuit Open
DD16 EPA07 (2007-09)Rated 0 out of 5 -
Detroit DD16 GHG14 (2014-16) Fault Code: SPN 3511 FMI 4 (CPC) Remote Accelerator Pedal Supply Voltage Circuit Failed Low
DD16 GHG14 (2014-16)Rated 0 out of 5 -
Volvo All Engines (2017 Emissions) Fault Code: U300A11 PID: ACM Key Position
All Engines (2017 Emissions)Rated 0 out of 5 -
PACCAR MX (2004 Emissions) Fault Code: U17C8 CAN – Message (TSC1_VXR) Time-Out
MX (2004 Emissions)Rated 0 out of 5 -
Detroit DD13 EPA10 (2010-13) Fault Code: SPN 625 FMI 9 (CPC) Message Not Received or has Stopped Arriving
DD13 EPA10 (2010-13)Rated 0 out of 5 -
Detroit DD13 EPA10 (2010-13) Fault Code: SPN 1639 FMI 2 (MCM) Fan Speed Error
DD13 EPA10 (2010-13)Rated 0 out of 5